The dryer doesn't usually fail all at once. It gets slower. Loads take longer. Eventually they come out still damp and you run them again. Then the heat stops altogether. By that point, the fault that caused the final failure has often been running for weeks — and in many cases it's created secondary damage that wouldn't have existed if the original signal had been caught earlier. BW Washer & Dryer Repair handles dryer faults across Charlotte, TN with technicians who understand this progression, stock the most common parts, and include a vent assessment on every single visit — because a dryer repair that skips the vent isn't a complete repair.
Structured diagnostics. Common parts stocked. Vent assessment on every visit.
Thermal fuse testing, heating element inspection, high-limit thermostat assessment, and cycling thermostat check. Four components, tested in order of cost and likelihood. The least expensive fix gets ruled in or out first.
Gas valve coil testing, igniter assessment, flame sensor inspection, and thermal fuse replacement. Gas dryer diagnostics follow a specific safety-conscious sequence every time.
Heating element replacement, thermal cutoff assessment, and control board diagnostics for all major brands including Samsung, LG, Whirlpool, GE, Maytag, Frigidaire, Electrolux, and Bosch.
A drum that spins freely by hand but won't turn under motor power is almost always the drive belt. We carry replacement belts for all high-volume residential models.
The most common dryer repair BW performs. Every thermal fuse replacement includes a vent assessment, because the fuse blew for a reason and that reason is almost always the vent.
For all major brands. Common configurations are stocked on the vehicle; less common ones are sourced and fitted on a return visit within a few days.
Gas line confirmation, vent duct connection, levelling, and a verified heat cycle before the job closes.
There's a window in every dryer fault where the problem is cheap to fix. It usually presents as longer drying times — loads that used to finish in 45 minutes stretching to 60, then 75. Most homeowners adjust. They run smaller loads, select higher heat, or just accept that the dryer is "getting old." The dryer isn't getting old. It's telling you the vent is restricting airflow and the thermal fuse is under stress.
When the fuse blows — and it will — the dryer stops heating entirely. At that point in Charlotte, TN, BW gets the call. The fuse gets replaced. The vent gets inspected. What we find most often is a duct that's anywhere from 40% to 80% blocked with lint compaction. The fuse failed because the vent made it inevitable. Catch it at the "longer drying times" stage and it's a vent cleaning and maybe a fuse. Catch it after the fuse has blown is the same job plus an emergency visit. Same problem. Different timing. Very different cost.
BW includes full vent duct assessment on every visit in Charlotte, TN.
There is no version of a correct dryer repair that doesn't include the vent. The vent is why most thermal fuses fail. It's why most heating elements run hotter than they should. It's why dryers that were "just repaired" come back for the same fault six weeks later. BW includes a vent duct assessment — from the machine connection to the exterior exit — on every dryer repair visit in Charlotte, TN as a standard part of the job. If the duct is restricted, we clear it. If it's configured with too many bends or is using flexible foil duct where rigid metal is recommended, we advise on what a corrected installation would involve. The repair isn't done until the vent condition is confirmed.
Load comes out actually dry
Consistent heat throughout cycle
Vent duct confirmed clear
That's what a dryer repair done correctly looks like. It's not a harder standard to meet — it's just a more complete one than most services apply.
"Dryer had been taking 80-plus minutes on every load for weeks. I assumed it was just getting old. BW found the exhaust duct had over two inches of lint buildup and the thermal fuse was on the verge of blowing. Cleared the duct, replaced the fuse, and the dryer's been running 45-minute cycles ever since. Should have called earlier."
"I'd replaced the thermal fuse myself twice — found the instructions online. It kept blowing. BW found the issue: the duct had a sharp 90-degree bend right at the wall connection that was choking airflow. They reconfigured it with a proper elbow and replaced the fuse. Four months later, no issues."
"Gas dryer stopped heating. I was dreading a gas valve replacement based on what I'd read. BW diagnosed open-circuit valve coils — a much less expensive fix. Done same visit, machine running perfectly through the first post-repair load. Relieved and impressed."
BW Washer & Dryer Repair serves Charlotte, TN with dryer repairs that include the vent, verify the result, and address the cause — not just the component. Book a technician today.
Click Here to Call (888) 910-4766